Assembly and application of vortex high pressure blower:

1、就把機器設備豎直或立式安裝在穩定的地區，防止在運轉時因地不整平而不停的震動產生偏倚，要保證 周邊環境的清理、干躁、自然通風暢順等，假如達不了這種應用標準，可采取更好的措施和解決方法，以更風機長期的運作造就有益的標準。

1. Install the machinery and equipment vertically or vertically in a stable area to prevent bias caused by non-stop vibration due to uneven ground during operation. Ensure the cleaning, dryness and smooth natural ventilation of the surrounding environment. If this application standard cannot be reached, better measures and solutions can be taken to create a beneficial standard with the long-term operation of the fan.

2、風機的的轉動角度一定與電扇堵蓋上所標箭頭符號方位一致，此商品是不允許翻轉運作的，可是在短期內是還可以的翻轉，但應防止長期翻轉。

2. The rotation angle of the fan must be consistent with the direction of the arrow symbol marked on the electric fan plug. This product is not allowed to turn over, but it can turn over in a short time, but it should be prevented from turning over for a long time.

3、應用前或查詢選取的產品型號是哪樣的主要參數，那樣在采用的情況下，才可以達到的操縱，如風機在運行工作中時，壓力不能超出標識上邊標記的穩定工作壓力值，以防氣泵造成過大的熱能和電機超電流量負載造成電機的毀壞。

3. What are the main parameters of the selected product model before application or query, so that the operation can be achieved only when it is adopted. For example, when the fan is running, the pressure cannot exceed the stable working pressure value marked on the mark, so as to prevent the motor from being damaged by excessive heat energy caused by the air pump and excessive electric flow load of the motor.

4、該類髙壓漩渦風機除開電機電機轉子與離心葉輪處的2個軸承外，其他身體部位沒有直接接觸磨擦，因此 不容易傳出物件碰擦的響聲，也不會造成異常響聲，如果有便是內部吸進到物品了，就清查取下。

4. Except for the two bearings at the motor rotor and centrifugal impeller, other body parts of this kind of high-pressure vortex fan do not have direct contact and friction, so it is not easy to send out the sound of object collision and will not cause abnormal sound. If there is any, it is the internal suction of objects, so check and remove them.

渦旋式氣泵的軸承安裝方法具體分二類。一類氣泵端軸承安裝在電機電動機軸和離心葉輪正中間的泵身體，這類氣泵平常不用加潤滑油脂。

The bearing installation methods of scroll air pump are divided into two categories. A type of air pump end bearing is installed in the pump body directly between the motor shaft and the centrifugal impeller. This kind of air pump usually does not need to add lubricating grease.

二類氣泵端軸承是組裝在泵蓋正中間，該類氣泵端軸承應定時加潤滑油脂(7018快速潤滑油脂)。針對三班持續作業的氣泵理應提升給油頻次。該類氣泵電機風機端軸承維修保養按一類氣泵。

The bearing at the end of class II air pump is assembled in the middle of the pump cover. The bearing at the end of this kind of air pump should be lubricated regularly (7018 quick lubricating grease). The oil feeding frequency of the air pump for continuous operation in the third shift should be increased. The maintenance of the fan end bearing of this kind of air pump motor is based on class I air pump.

維護保養與維護保養：

Maintenance and maintenance:

風機在經由長期的運行以后，出入氣兩邊的濾網和除掉噪音設備應做好清理，以發生免阻塞危害到應用實際效果。此外強烈進排氣口外連接采用塑料軟管連接(如橡膠軟管、塑膠扭簧管)，好不必采用硬鏈接，以防產生振動時危害管路聯接。

After long-term operation of the fan, the filter screens on both sides of the air inlet and outlet and the noise removal equipment shall be cleaned to avoid blocking and harm the actual application effect. In addition, it is strongly recommended to use plastic hose connection (such as rubber hose and plastic torsion reed pipe) for the external connection of air inlet and exhaust port. It is not necessary to use hard link, so as to prevent endangering the pipeline connection in case of vibration.

氣泵軸承的拆換：拆換軸承務必由了解維修工作中的人開展實際操作。先扭松泵蓋緊的螺絲，隨后按頂角的次序逐一拆裝零件，拆下來的零件應歷經清理，隨后按反次序安裝。

Disassembly and replacement of air pump bearing: the actual operation of disassembly and replacement of bearing must be carried out by people who understand the maintenance work. First loosen the screws on the pump cover, and then disassemble the parts one by one according to the order of the top angle. The removed parts should be cleaned and then installed in the reverse order.

可是一定要留意，在拆裝時，不可以硬撬離心葉輪和軸承，應當采用專用型的拉馬拉出。在運轉時也要留意，風機是禁止固態、液態及有浸蝕汽體進到泵殼，

However, it must be noted that during disassembly and assembly, the centrifugal impeller and bearing cannot be pried hard, and the special Ramallah should be used. During operation, it should also be noted that solid, liquid and etched steam are prohibited from entering the pump casing,

本文的精彩內容由湖北水產增氧設備提供知識提供，本網站還有很多的精彩內容，更多的內容您可以點擊進入：http://www.lzdbgs.com.cn/我們有專門的客服為您解答問題

The wonderful content of this article is provided by Hubei aquatic oxygenation equipment. There are many wonderful contents on this website. You can click to enter more contents: http://www.lzdbgs.com.cn/ We have special customer service to answer your questions